Can I Set Up A Tub Myself?
Can I Set Up A Tub Myself?
Blog Article
This post which follows about A Step-by-Step Guide to Installing a Bathtub is rather intriguing. You should look it over.
Setting up a tub isn't exactly rocket science, but it does require strong plumbing, woodworking, and also often, tiling abilities. Replacing an old tub with a new one is also a moderately hard task. If the old bathtub is easily available, the project can move speedily; if you need to open up a wall to remove the old bathtub and also place the brand-new bathtub, the task is a lot harder. In either instance, the job is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub and also set in the new one. Make sure you have actually certified yourself for the task and are comfortable trying it. Instead of employing a professional to take over a halfway-completed job, it is better to consider using one before you begin. Opportunities are you may need a specialist plumber to make tube links.
This article will certainly assist you install a brand-new tub in your washroom if you have actually currently gotten a new bathtub as well as don't require to alter the setup of your previous water system pipes.
Your devices as well as material checklist need to make up the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing taps can be quite troublesome due to the limited gain access to that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will certainly come from the pipes. When the supply pipes have actually been removed, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end gives a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin making certain that the washing machines are in place between the tap as well as the sink. Safeguard the faucet in position with the manufacturer offered backnut. When the tap is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap adapters. The former kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bathtub
Using the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are useful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as adjusting the feet on the bathtub until the spirit level reviews degree.
To mount faucets, fit the bottom of the furthest flexible faucet adapter to the ideal supply pipeline by making a compression join; then do the same for the other faucet.
Activate the water system as well as check all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise inspect the overflow outlet and also the regular outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub must wait until the bathtub has actually been utilized at least when as this will certainly settle it right into its last position.
Preparing for the Installment
First of all, the supporting framework supplied with the bathroom ought to be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the versatile faucet ports to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its last placement.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to break a stiff seal, creating the water to penetrate the wall in between the bathroom and the tiling, causing difficulties with dampness as well as feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked newspaper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to permit the motion experienced when the bathtub remains in usage. The sealant can crack relatively early if you do not take into consideration this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the marketplace. It is advisable to fit the tiles using water-resistant or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic reader on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I figured sharing that piece of content was really helpful. Liked our posting? Please share it. Let someone else check it out. Thanks for taking the time to read it.
Try Here
Report this page